★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 642-813 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/642-813-dumps.html
Everything youll need in the 642-813 certification exam can be included in the Cisco 642-813 practice materials. The professionals keep the Cisco Cisco certification exam dumps updated and also revised constantly. The particular price can be reasonable and the time a person spend can be worthy of. Each 642-813 exam question is equipped together with correct and also verified answer in details. Regular updates about the basis of the true Cisco 642-813 exam questions. Every customer can please take a quiz before acquiring our Cisco Cisco product or service. Come to be able to http://www.Examcollection.com proper now. Every one of the valuable 642-813 simulated tests will likely be presented for your requirements. Download the check engine software, and also preview the Cisco exam with anywhere and also anytime.
2021 Oct cbt nuggets cisco ccnp switch 642-813:
Q81. DRAG DROP
Match the Attributes on the left with the types of VLAN designs on the right.
Answer:
Q82. You are the administrator of a switch and currently all host-connected ports are configured with the portfast command. You have received a new directive from your manager that states that, in the future, any host-connected port that receives a BPDU should automatically disable PortFast and begin transmitting BPDUs. Which command will support this new requirement?
A. Switch(config)#spanning-tree portfast bpduguard default
B. Switch(config-if)#spanning-tree bpduguard enable
C. Switch(config-if)#spanning-tree bpdufilter enable
D. Switch(config)#spanning-tree portfast bpdufilter default
Answer: D
Q83. Which statement about the EIGRP routing being performed by the switch is true?
A. The EIGRP neighbor table contains 20 neighbors.
B. EIGRP is running normally and receiving IPv4 routing updates.
C. EIGRP status cannot be determined. The command show ip eigrp topology would determine the routing protocol status.
D. The switch has not established any neighbor relationships. Further network testing and troubleshooting must be performed to determine the cause of the problem.
Answer: D
Q84. DRAG DROP
Place the syslog message types in the left to the corresponding area on the right, based on priority from highest to lowest.
Answer:
Q85. Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways?
A. IRDP
B. HSRP
C. GLBP
D. VRRP
Answer: C
Up to the minute cisco 642-813 labs:
Q86. When you create a network implementation for a VLAN solution, what is one procedure that you should include in your plan?
A. Perform an incremental implementation of components.
B. Implement the entire solution and then test end-to-end to make sure that it is performing as designed.
C. Implement trunking of all VLANs to ensure that traffic is crossing the network as needed before performing any pruning of VLANs.
D. Test the solution on the production network in off hours.
Answer: A
Q87. Refer to the exhibit.
Both routers are configured for the GLBP. Which statement is true?
A. The default gateway addresses of both hosts should be set to the IP addresses of both routers.
B. The default gateway address of each host should be set to the virtual IP address.
C. The hosts learn the proper default gateway IP address from router A.
D. The hosts have different default gateway IP addresses and different MAC addresses for each router.
Answer: B
Q88. DRAG DROP
Drop
Answer:
Q89. Which statement about when standard access control lists are applied to an interface to control inbound or outbound traffic is true?
A. The best match of the ACL entries is used for granularity of control.
B. They use source IP information for matching operations.
C. They use source and destination IP information for matching operations.
D. They use source IP information along with protocol-type information for finer granularity of control.
Answer: B
Q90. CORRECT TEXT
AAAdot1x Lab
Acme is a small shipping company that has an existing enterprise network comprised of 2 switches;DSW1 and ASW2. The topology diagram indicates their layer 2 mapping. VLAN 40 is a new VLAN that will be used to provide the shipping personnel access to the server. For security reasons, it is necessary to restrict access to
VLAN 20 in the following manner:
- Users connecting to ASW1's port must be authenticate before they are given access to the network.
-Authentication is to be done via a Radius server:
- Radius server host: 172.120.39.46
- Radius key: rad123
- Authentication should be implemented as close to the host device possible.
- Devices on VLAN 20 are restricted to in the address range of 172.120.40.0/24.
- Packets from devices in the address range of 172.120.40.0/24 should be passed on VLAN 20.
- Packets from devices in any other address range should be dropped on VLAN 20.
- Filtering should be implemented as close to the server farm as possible.
The Radius server and application servers will be installed at a future date. You have been tasked with implementing the above access control as a pre-condition to installing the servers. You must use the available
IOS switch features.
Answer: The configuration:
Step1: Console to ASW1 from PC console 1
ASW1(config)#aaa new-model
ASW1(config)#radius-server host 172.120.39.46 key rad123 ASW1(config)#aaa authentication dot1x default group radius ASW1(config)#dot1x system-auth-control
ASW1(config)#inter fastEthernet 0/1
ASW1(config-if)#switchport mode access
ASW1(config-if)#dot1x port-control auto
ASW1(config-if)#exit
ASW1#copy run start
Step2: Console to DSW1 from PC console 2
DSW1(config)#ip access-list standard 10
DSW1(config-ext-nacl)#permit 172.120.40.0 0.0.0.255
DSW1(config-ext-nacl)#exit
DSW1(config)#vlan access-map PASS 10
DSW1(config-access-map)#match ip address 10
DSW1(config-access-map)#action forward
DSW1(config-access-map)#exit
DSW1(config)#vlan access-map PASS 20
DSW1(config-access-map)#action drop
DSW1(config-access-map)#exit
DSW1(config)#vlan filter PASS vlan-list 20
DSW1#copy run start