★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 300-360 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/300-360-dumps.html


It is impossible to pass Cisco 300-360 exam without any help in the short term. Come to Ucertify soon and find the most advanced, correct and guaranteed Cisco 300-360 practice questions. You will get a surprising result by our Regenerate Designing Cisco Wireless Enterprise Networks practice guides.

2021 Mar 300-360 actual test

Q1. A customer has dual-band devices that they want to use 40 MHz channels. If the customer is using Cisco 3600 Series access points with a 5508 controller. Which setting assists with this change?

A. Enable band select globally.

B. Enable aggressive load balancing.

C. Disable lower data rates on 802 .11G GHz radios.

D. Disable overlapping 802.11G channels.

Answer: A


Q2. As part of a wireless site survey in a hospital, an engineer needs to identify potential Layer 1 interferers. In which three areas is the engineer most likely expect to find sources of 2.4 GHz and 5 GHz RF noise? (Choose three.)

A. emergency room

B. magnetic resonance imaging

C. laboratory

D. X-ray radiography

E. Gamma Knife radiation treatment

F. kitchen

Answer: A,C,F


Q3. You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data. How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?

A. Use the centralized deployment method in the data center with the N + N redundancy method.

B. Use the centralized deployment method in the data center with the N + 1 redundancy method

C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clientSSO.

D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.

E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.

F. Use the distributed deployment method in each building MDF with the N + N redundancy method.

Answer: C


Q4. An engineer must design wireless coverage in thick-walled stairwells. Which information should the engineer refer to when determining where APs can be installed?

A. Local or National Building Code

B. IEEE

C. BICSI TDMM

D. Cisco Hardware Installation Guide

Answer: D


Q5. Refer to the exhibit.

While testing the post-deployment WLAN network, you discover that an AP has been placed in a difficult area.

The AP cannot be moved easily because of various requirements. The client performance of various Apple and Microsoft operating system-based products does not meet expectations. Which two options can help mitigate the performance issue? (Choose two.)

A. Add additional APs.

B. Increase the AP power level to maximum.

C. Rotate the AP 90 degrees to change antenna polarity.

D. Replace the AP with an AP and external antenna.

E. Change the AP location to one that is less RF hostile.

Answer: A,D


Abreast of the times 300-360 exam question:

Q6. When conducting a wireless survey at a customer facility, signal attenuation in an area that is surrounded by thick glass walls is noted as 2dB. When configuring Cisco Prime Infrastructure, which obstacle should be placed in a map editor to represent the impact the glass wall will have on the RF signal in the facility?

A. heavy door

B. thick wall

C. glass

D. light wall

Answer: D

Explanation: Reference: http://www.cisco.com/c/en/us/td/docs/wireless/prime_infrastructure/1-2/configuration/guide/pi_12_cg/maps.html Table 6-4


Q7. An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services. Which two requirements are inputs to the design? (Choose two.)

A. overlapping -67 dBm coverage from three access points

B. overlapping -75 dBm coverage from three access points

C. overlapping-72 dBm coverage from two access points

D. continuous -67 dBm coverage from one access point

E. continuous -72 dBm coverage from one access point

Answer: B,D

Explanation:

http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob73dg/emob73/ch3_WLAN.html#pgfId-1000250


Q8. A customer has deployed an N+N redundant wireless infrastructure. In this deployment, the access points have been salt and peppered between controllers. What configuration would be necessary to cut down on the use of mobility tunnels for voice clients?

A. mobility anchor

B. KIS based CAC

C. media session snooping

D. re-anchor roamed voice clients

Answer: D


Q9. An engineer is determining the signal levels for the wireless cells. Which signal-to-noise ratio is an optimal configuration to achieve?

A. minimum SNR of -33 dBm

B. minimum SNR of -25 dBm

C. minimum SNR of 25 dB

D. minimum SNR of 33 dB

Answer: C

Explanation:

The minimum recommended wireless signal strength for voice applications is -67 dBm and the minimum SNR is 25 dB.

Reference: http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-sitesurvey-guidelines-wlan-00.html


Q10. Which list of characteristics must all controllers in a mobility group have in common based on best practices?

A. mobility group name, version of controller code, Control and Provisioning of Wireless Access Points mode,ACLs, and WLANs (SSIDs)

B. mobility domain name, version of controller code, and Control and Provisioning of Wireless Access Pointsmode

C. mobility domain name, version of controller code, Control and Provisioning of Wireless Access Pointsmode, ACLs, and WLANs (SSIDs)

D. mobility group name, version of controller code, and Control and Provisioning of Wireless Access Pointsmode

Answer: A