★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-120 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/200-120-dumps.html
We offer that you will get over the Cisco Cisco exam with ease. Our experienced professionals are generally devoted to be able to updating the Cisco 200-120 exam dumps. It is possible to keep faith in us and we offer 100% money back. If you have something wrong with our 200-120 practice goods, please contact us timely. We have 24/7 customer support.
2021 Sep testinside 200-120:
Q81. - (Topic 1)
Refer to exhibit:
Which destination addresses will be used by Host A to send data to Host C? (Choose two.)
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C D. the MAC address of Host C
E. the IP address of the router's E0 interface
F. the MAC address of the router's E0 interface
Answer: C,F
Q82. - (Topic 7)
Refer to the exhibit.
HostA cannot ping HostB. Assuming routing is properly configured, what is the cause of this problem?
A. HostA is not on the same subnet as its default gateway.
B. The address of SwitchA is a subnet address.
C. The Fa0/0 interface on RouterA is on a subnet that can't be used.
D. The serial interfaces of the routers are not on the same subnet.
E. The Fa0/0 interface on RouterB is using a broadcast address.
Answer: D
Q83. - (Topic 4)
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
Q84. CORRECT TEXT - (Topic 7)
Answer: On the MGT Router:
Config t Router eigrp 12 Network 192.168.77.0
Q85. - (Topic 4)
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.
Answer: E
Up to the immediate present ccna test 200-120:
Q86. - (Topic 5)
What levels will be trapped if the administrator executes the command
router(config)# logging trap 4 (Choose four)
A. Emergency
B. Notice
C. Alert
D. Error
E. Warning
Answer: A,C,D,E
Q87. - (Topic 5)
What command instructs the device to timestamp Syslog debug messages in milliseconds?
A. service timestamps log datetime localtime
B. service timestamps debug datetime msec
C. service timestamps debug datetime localtime
D. service timestamps log datetime msec
Answer: B
Q88. - (Topic 2)
Refer to the exhibit.
At the end of an RSTP election process, which access layer switch port will assume the discarding role?
A. Switch3, port fa0/1
B. Switch3, port fa0/12
C. Switch4, port fa0/11
D. Switch4, port fa0/2
E. Switch3, port Gi0/1
F. Switch3, port Gi0/2
Answer: C
Q89. - (Topic 2)
Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)
A. 802.1d
B. VTP
C. 802.1q
D. STP
E. SAP
Answer: A,D
Q90. - (Topic 1)
Refer to the exhibit.
What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.)
A. The number of collision domains would remain the same.
B. The number of collision domains would decrease.
C. The number of collision domains would increase.
D. The number of broadcast domains would remain the same.
E. The number of broadcast domains would decrease.
F. The number of broadcast domains would increase.
Answer: C,D