★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 642-997 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/642-997-dumps.html


Q11. Which command sequence correctly enables Adapter FEX on Nexus 5000 Series Switches? 

A. switch(config)# install feature-set virtualization switch(config)# feature-set virtualization 

B. switch(config)# install feature-set adapter-fex switch(config)# feature-set adapter-fex 

C. switch(config)# install feature-set adapter-fex switch(config)# feature-set virtualization 

D. switch(config)# install feature-set virtualization switch(config)# feature-set adapter-fex 

Answer: A 


Q12. Refer to the exhibit. 

Which corrective action is taken to resolve the problem? 

A. Trunk four VLANs on interface ethernet 199/1/1. 

B. Use the shut and no shut interface ethernet 199/1/1so that the VLANs come up. 

C. Place interface ethernet 199/1/1 in VLAN 4 in the N5K-2 configuration. 

D. Prune all but four VLANs from vPC 199. 

E. Add VLAN 4 to vPC 199. 

Answer: C 


Q13. Which three selections represent implementations of Cisco VN-Link technology? (Choose three.) 

A. Cisco Nexus 1000V 

B. Cisco Nexus 2000 FEX 

C. Cisco VM-FEX 

D. VMware PTS 

E. vMotion 

Answer: ACD 


Q14. Which two statements about SAN zoning on Cisco Nexus switches are true? (Choose two.) 

A. Zoning is enforced by examining the destination ID field. 

B. Devices can only belong to one zone. 

C. Only one zone set can be activated at any time. 

D. A zone can only be a member one zone set. 

E. Zoning must be administered from the primary SAN switch in the fabric. 

F. Zone configuration changes are nondisruptive. 

Answer: CF 


Q15. Which GLBP load-balancing algorithm ensures that a client is always mapped to the same VMAC address? 

A. vmac-weighted 

B. dedicated-vmac-mode 

C. shortest-path and weighting 

D. host-dependent 

Answer: D 


Q16. Which topology is not supported when using vPC? 

A. a single-homed server to a single FEX that is connected to two Cisco Nexus 5500 Series Switches 

B. a dual-homed server to two FEXs, each connected to two Cisco Nexus 5500 Series Switches 

C. a dual-homed server to two FEXs that are connected to one Cisco Nexus 5500 Series Switch 

D. a dual-homed server to a single FEX that is connected to two Cisco Nexus 5500 Series Switches 

Answer: C 


Q17.  

FabricPath switch-id is 25 and load-balance is configured for L3/L4 and rotate amount is 14 byte. What information is true about FabricPath switch-id? 

A. FabricPath topology requires manual configuration of switch-id which has a range from 1 to 4095 

B. Every FabricPath must have a manually configured switch-id for it to form a FabricPath topology 

C. FabricPath topology requires manual configuration of switch-id which has a range from 1 to 4099 

D. You do not have to manually assign a switch ID unless you are running a virtual port channel plus (vPC*) because the system assigns a switch ID for you when you enable FabricPath 

Answer: B


Q18. Which two statements about Cisco Nexus 7000 line cards are true? (Choose two.) 

A. M1, M2, and F1 cards are allowed in the same VDC. 

B. M line cards are service-oriented and likely face the access layer and provide Layer 2 connectivity. 

C. F line cards are performance-oriented and likely connect northbound to the core layer for Layer 3 connectivity. 

D. M line cards support Layer 2, Layer 3, and Layer 4 with large forwarding tables and a rich feature set. 

E. The F2 line card must reside in the admin VDC. 

Answer: AD 


Q19.  

When configuring FCoE VLANs and Virtual Fiber Channel (vFC) Interfaces, what guidelines must be followed? 

A. Each vFC interface must be bound to an FCoE-enabled Ethernet or EtherChannel interface or to the MAC address of a remotely connected adapter 

B. Each FC interface must be bound to an FCoE-enabled Ethernet or EtherChannel interface or to the MAC address of a remotely connected adapter 

C. Each vFC interface must be bound to an FC enabled Ethernet or EtherChannel interface or to the MAC address of a remotely connected adapter 

D. Each vFC interface must be bound to an FCoE-enabled vFC or EtherChannel interface or to the MAC address of a remotely connected adapter 

Answer: A 


Q20. Which statement about implementation of Cisco TrustSec on Cisco Nexus 5546 or 5548 switches are true? 

A. Cisco TrustSec support varies depending on Cisco Nexus 5500 Series Switch model. 

B. The hardware is not able to support MACsec switch-port-level encryption based on IEEE 802.1AE. 

C. The maximum number of RBACL TCAM user configurable entries is 128k. 

D. The SGT Exchange Protocol must use the management (mgmt 0) interface. 

Answer: B