★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 352-001 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/352-001-dumps.html
We promise that you can get the most logical along with fresh Cisco study supplies. Win through your weak aspects along with pass the Cisco Cisco exam together with high represents under the actual help associated with Cisco 352-001 training materials. Please take activities right currently! Its moment to place order! You will be on the method to Cisco 352-001 certification earlier along with easier. Your objective of Testking 352-001 exam braindumps is always to make you complete prepared for the Cisco 352-001 exam.
2021 Sep 352-001 ccde:
Q11. A network designer is working with a company to improve convergence at the Layer 2 control plane and decides to use LACP. Which of these components does LACP use to create the system ID?
A. LACP system priority and switch MAC address
B. LACP port priority and switch MAC address
C. LACP port priority and port number
D. LACP system priority and port number
Answer: A
Q12. A network design shows two routers directly connected to an Ethernet switch using optical connections. There is an OSPF adjacency between the routers. In this design, which solution will ensure that interface down detection is reported as quickly as possible to the IGP?
A. optimized OSPF SPF timers
B. Bidirectional Forwarding Detection
C. automatic protection switching
D. optimized OSPF LSA timers
E. Ethernet OAM CFM monitoring
Answer: B
Q13. What are two benefits of following a structured hierarchical and modular design? (Choose two.)
A. Each component can be designed independently for its role.
B. Each component can be managed independently based on its role.
C. Each component can be funded by different organizations based on its role.
D. Each component can support multiple roles based on the requirements.
E. Each component can provide redundancy for applications and services.
Answer: AB
Q14. In order to meet your service level agreement, your network designer created a design solution that includes interface dampening. In which two ways will interface dampening benefit your overall network design? (Choose two.)
A. Interface dampening uses an exponential backoff algorithm to suppress event reporting to the upper-level protocols.
B. When the interface is dampened, further link events are not reported to the upper protocol modules.
C. When the interface is dampened, further link events are reported to the upper protocol module.
D. Periodic interface flapping that affects the routing system as a whole should have a period shorter than the system convergence time.
Answer: AB
Q15. You have been asked to design a wireless network solution that will implement context-aware services on an existing network that was initially deployed for data traffic only. Which two design principles would you follow to increase the location accuracy with the least possible impact on the current setup? (Choose two.)
A. Use directional antennas to provide better cell separation.
B. Add access points along the perimeter of the coverage area.
C. Install additional APs in monitor mode where the cochannel interference would otherwise be affected.
D. Increase the AP density to create an average interaccess point distance of less than 40 ft.
E. Fine tune the access points radio configuration to have a higher average transmission power to achieve better coverage.
Answer: BC
Avant-garde 352-001 p4s:
Q16. Refer to the exhibit.
A service provider would like to use Ethernet OAM to detect end-to-end connectivity failures between SP-SW1 and SP-SW2. In which two of these ways can you design this solution? (Choose two.)
A. Enable Y.1731 Connectivity Fault Management on the SP switches.
B. E-LMI PDUs must be forwarded over VPLS.
C. Cisco Discovery Protocol PDUs must be forwarded over the VPLS.
D. Use upward maintenance endpoints on the SP switches.
E. Enable IEEE 802.1ag Connectivity Fault Management on the SP switches.
Answer: DE
Q17. You are creating a network design that will influence the traffic path across the MPLS core on a virtual private LAN. Which parameter is included in your design to manage the traffic?
A. Deploy MPLS traffic engineering and modify the path using the preferred path.
B. Deploy MPLS traffic engineering and modify the path using auto-route, static routing, or PBR.
C. Create an MPLS traffic engineering tunnel and modify the path using a static route.
D. Create an MPLS traffic engineering tunnel and modify the path using auto-route announce.
Answer: A
Q18. You have been tasked to create a Layer 2 network design that uses vPC to provide resiliency and avoid loops. vPC removes Layer 2 loops while providing redundancy through which mechanism?
A. dual-active detection
B. address synchronization
C. strict forwarding rules
D. Bridge Assurance
Answer: C
Q19. You are the lead IP/MPLS network designer of a service provider called XYZ. You are leading a design discussion regarding IPv6 implementation in the XYZ MPLS network, using MPLS 6PE/6VPE techniques. Currently, XYZ provides IPv4 multicast services over an MPLS network by using MVPN, and would like to provide parallel IPv6 multicast services. Which three multicast solutions should be enabled? (Choose three.)
A. native IPv6, only for multicast services
B. MPLS 6PE/6VPE, because it provides IPv6 multicast support by default
C. an overlay model using Layer 2 MPLS tunnels
D. PIM-DM to enable IPv6 multicast in conjunction with MPLS 6PE/6VPE
E. MVPN for IPv6 multicast service
Answer: ACE
Q20. As a service provider you must support a Layer 2 virtualization protocol that does not include the use of label switching. Which option can meet this design requirement?
A. VPLS
B. VRF-Lite
C. QinQ
D. 802.3ad
Answer: C