★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/200-125-dumps.html
Q91. - (Topic 7)
Which protocol can cause overload on a CPU of a managed device?
A. Netflow
B. WCCP
C. IP SLA
D. SNMP
Answer: D
Explanation:
Sometimes, messages like this might appear in the router console:
%SNMP-3-CPUHOG: Processing [chars] of [chars]
They mean that the SNMP agent on the device has taken too much time to process a request.
You can determine the cause of high CPU use in a router by using the output of the show process cpu command.
Note: A managed device is a part of the network that requires some form of monitoring and
management (routers, switches, servers, workstations, printers…).
Q92. - (Topic 5)
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Answer: B,C
Explanation:
✑ A single interface may be assigned multiple addresses of any type (unicast, anycast, multicast).
✑ Every IPv6-enabled interface must contain at least one loopback and one link-local
address.
✑ Optionally, every interface can have multiple unique local and global addresses.
Reference: IPv6 Addressing at a Glance – Cisco PDF
Q93. - (Topic 8)
What is the danger of the permit any entry in a NAT access list?
A. It can lead to overloaded resources on the router.
B. It can cause too many addresses to be assigned to the same interface.
C. It can disable the overload command.
D. It prevents the correct translation of IP addresses on the inside network.
Answer: A
Q94. - (Topic 8)
While troubleshooting a connection problem on a computer, you determined that the computer can ping a specific web server but it cannot connect to TCP port 80 on that server. Which reason for the problem is most likely true?
A. A VLAN number is incorrect.
B. A Route is missing
C. An ARP table entry is missing.
D. An ACL is blocking the TCP port.
Answer: D
Q95. - (Topic 5)
Refer to the exhibit.
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)
A. Network A - 172.16.3.48/26
B. Network A - 172.16.3.128/25
C. Network A - 172.16.3.192/26
D. Link A - 172.16.3.0/30
E. Link A - 172.16.3.40/30
F. Link A - 172.16.3.112/30
Answer: B,D
Explanation:
Only a /30 is needed for the point to point link and sine the use of the ip subnet-zero was used, 172.16.3.0/30 is valid. Also, a /25 is required for 120 hosts and again 172.16.3.128/25 is the best, valid option.
Q96. - (Topic 8)
Which statement about LLDP is true?
A. It is a Cisco proprietary protocol.
B. It is configured in global configuration mode.
C. The LLDP update frequency is a fixed value.
D. It runs over the transport layer.
Answer: B
Q97. - (Topic 8)
If the primary root bridge experiences a power loss, which switch takes over?
A. switch 0004.9A1A.C182
B. switch 00E0.F90B.6BE3
C. switch 00E0.F726.3DC6
D. switch 0040.0BC0.90C5
Answer: A
Q98. - (Topic 8)
Which method does a connected trunk port use to tag VLAN traffic?
A. IEEE 802 1w
B. IEEE 802 1D
C. IEEE 802 1Q
D. IEEE 802 1p
Answer: C
Explanation:
http://www.cisco.com/c/en/us/support/docs/lan-switching/8021q/17056-741-4.html
Q99. - (Topic 5)
Syslog was configured with a level 3 trap. Which 3 types of logs would be generated (choose four)
A. Emergencies
B. Alerts
C. Critical
D. Errors
E. Warnings
Answer: A,B,C,D
Explanation:
The Message Logging is divided into 8 levels as listed below: Level Keyword Description
0 emergencies System is unusable 1 alerts Immediate action is needed 2 critical Critical conditions exist
3 errors Error conditions exist
4 warnings Warning conditions exist
5 notification Normal, but significant, conditions exist 6 informational Informational messages
7 debugging Debugging messages
The highest level is level 0 (emergencies). The lowest level is level 7. If you specify a level with the “logging console level” command, that level and all the higher levels will be
displayed. For example, by using the “logging console warnings” command, all the logging of emergencies, alerts, critical, errors, warnings will be displayed.
Q100. CORRECT TEXT - (Topic 8)
Which protocol authenticates connected devices before allowing them to access the LAN?
A. 802.1d
B. 802.11
C. 802.1w
D. 802.1x
Answer: D
Explanation:
802.1X authentication involves three parties: a supplicant, an authenticator, and an authentication server. The supplicant is a client device (such as a laptop) that wishes to attach to the LAN/WLAN. The term 'supplicant' is also used interchangeably to refer to the software running on the client that provides credentials to the authenticator. The
authenticator is a network device, such as an Ethernet switch or wireless access point; and the authentication server is typically a host running software supporting the RADIUS and EAP protocols.
The authenticator acts like a security guard to a protected network. The supplicant (i.e., client device) is not allowed access through the authenticator to the protected side of the network until the supplicant’s identity has been validated and authorized. An analogy to this is providing a valid visa at the airport's arrival immigration before being allowed to enter the country. With 802.1X port-based authentication, the supplicant provides credentials, such as user name/password or digital certificate, to the authenticator, and the authenticator forwards the credentials to the authentication server for verification. If the authentication server determines the credentials are valid, the supplicant (client device) is allowed to access resources located on the protected side of the network.