★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-120 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/200-120-dumps.html
Buying each of our Cisco Cisco exam course, you may get: 1. Newest practice materials 2. Continuously available chat support and e-mail regarding technical help 3. 100% cash back assure and 99% passing ratio 4. Fast access in order to 200-120 dumps 5. Pass Cisco 200-120 exam on your 1st try without any issue 6. Designed around the basis of Cisco syllabus 7. A long time of knowledgeable experts
2021 Oct pass4sure ccna 200-120:
Q111. - (Topic 9)
Which type of address is the public IP address of a NAT device?
A. outside global
B. outside local
C. inside global
D. inside local
E. outside public
F. inside public
Answer: C
Q112. - (Topic 9)
Which three characteristics are representative of a link-state routing protocol? (Choose three.)
A. provides common view of entire topology
B. exchanges routing tables with neighbors
C. calculates shortest path
D. utilizes event-triggered updates
E. utilizes frequent periodic updates
Answer: A,C,D
Q113. - (Topic 7)
What would be the effect of issuing the command ip access-group 114 in to the fa0/0 interface?
A. Attempts to telnet to the router would fail.
B. It would allow all traffic from the 10.4.4.0 network.
C. IP traffic would be passed through the interface but TCP and UDP traffic would not.
D. Routing protocol updates for the 10.4.4.0 network would not be accepted from the fa0/0 interface.
Answer: B
Q114. - (Topic 8)
Refer to the exhibit.
What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?
A. The Serial0/0 interface is passing traffic.
B. The DLCI 100 was dynamically allocated by the router.
C. The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP server.
D. The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud.
E. The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP.
Answer: E
Q115. - (Topic 1)
For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)
A. to uniquely identify devices at Layer 2
B. to allow communication with devices on a different network
C. to differentiate a Layer 2 frame from a Layer 3 packet
D. to establish a priority system to determine which device gets to transmit first
E. to allow communication between different devices on the same network
F. to allow detection of a remote device when its physical address is unknown
Answer: A,E
Renew ccna 200-120 free practice test:
Q116. - (Topic 4)
Refer to the exhibit.
Which of these statements correctly describes the state of the switch once the boot process has been completed?
A. As FastEthernet0/12 will be the last to come up, it will be blocked by STP.
B. Remote access management of this switch will not be possible without configuration change.
C. More VLANs will need to be created for this switch.
D. The switch will need a different IOS code in order to support VLANs and STP.
Answer: B
Q117. - (Topic 3)
Which two benefits are provided by using a hierarchical addressing network addressing scheme? (Choose two.)
A. reduces routing table entries
B. auto-negotiation of media rates
C. efficient utilization of MAC addresses
D. dedicated communications between devices
E. ease of management and troubleshooting
Answer: A,E
Q118. - (Topic 2)
Based on the network shown in the graphic
Which option contains both the potential networking problem and the protocol or setting that should be used to prevent the problem?
A. routing loops, hold down timers
B. switching loops, split horizon
C. routing loops, split horizon
D. switching loops, VTP
E. routing loops, STP
F. switching loops, STP
Answer: F
Q119. - (Topic 3)
Which command enables IPv6 forwarding on a Cisco router?
A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor
Answer: C
Q120. - (Topic 3)
What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72?
A. B514 : 82C3 : 0029 : EC7A : EC72
B. B514 : 82C3 :: 0029 : EC7A : EC72
C. B514 : 82C3 : 0029 :: EC7A : 0000 : EC72
D. B514 : 82C3 :: 0029 : EC7A : 0 : EC72
Answer: D