★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 352-001 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/352-001-dumps.html


Proper study guides for Up to date Cisco CCDE Written Exam certified begins with Cisco 352-001 preparation products which designed to deliver the Simulation 352-001 questions by making you pass the 352-001 test at your first time. Try the free 352-001 demo right now.

2021 Dec sitecom wl-352 v3 001 driver:

Q81. During a network design review, it is recommended that the network with a single large area should be broken up into a backbone and multiple nonbackbone areas. There are differing opinions on how many ABRs are needed for each area for redundancy. What would be the impact of having additional ABRs per area? 

A. There is no impact to increasing the number of ABRs. 

B. The SPF calculations are more complex. 

C. The number of externals and network summaries are increased. 

D. The size of the FIB is increased. 

Answer: C 


Q82. Acme Corporation wants to minimize the risk of users plugging unauthorized switches and hubs into the network. Which two features can be used on the LAN access ports to support this design requirement? (Choose two.) 

A. BPDU Guard 

B. PortFast 

C. Loop Guard 

D. Port Security 

E. UDLD 

Answer: AD 


Q83. Refer to the exhibit. 

Which technology could be used in this design to provide link recovery and high traffic capacity? 

A. Rapid PVST 

B. MST 

C. PAgP 

D. Flex Links 

Answer: C 


Q84. Which three reasons to deploy an IDS sensor in promiscuous mode when you design a security solution are true? (Choose three.) 

A. Solution should be resistant to sensor failure. 

B. Solution should allow for stream normalization. 

C. Solution should not impact jitter and latency for voice traffic. 

D. Solution should allow for signature-based pattern matching. 

E. Solution should allow to deny packets inline. 

Answer: ACD 


Q85. Which three techniques can be used to improve fault isolation in an enterprise network design? (Choose three.) 

A. aggregate routing information on an OSPF ABR 

B. fully meshed distribution layer 

C. Equal-Cost Multipath routing 

D. EIGRP query boundaries 

E. multiple IS-IS flooding domains 

F. tuned Spanning Tree Protocol timers 

Answer: ADE 


Improve 352-001 actual test:

Q86. ACME Corporation is integrating IPv6 into their network, which relies heavily on multicast distribution of data. Which two IPv6 integration technologies support IPv6 multicast? (Choose two.) 

A. 6VPE 

B. 6PE 

C. dual stack 

D. ISATAP 

E. 6to4 

F. IPv6INIP 

Answer: CF 


Q87. Refer to the exhibit. 

After this new OSPF design with per-packet load balancing was implemented, Host A reported that large file downloads from Server A became slow and sometimes failed. The operations team discovered that packets are arriving out of order on R1. Which cost-conscious redesign action will fix the issue? 

A. Upgrade all links to 10 Gbps. 

B. Add an IP SLA probe on R1 and R4. 

C. Adjust the OSPF auto-cost reference bandwidth on R4. 

D. Adjust the OSPF auto-cost reference bandwidth on all routers. 

Answer: D 


Q88. Refer to the exhibit. 

Four customer sites are connected through an EoMPLS-based VPLS over an MPLS provider. You are migrating from OSPF to multi-level IS-IS as the routing protocol to run on the four CE routers, and connectivity between all four sites is required. You want to control which CE or CEs will be elected as the Designated Intermediate System. Which two key aspects should be taken into account? (Choose two.) 

A. The DIS role for Level1 and Level2 can be performed by different routers. 

B. The CE with the second highest priority will be elected as the backup DIS on the LAN segment. 

C. One of the CE routers will be elected as the DIS based on interface priority then highest MAC address. 

D. It is recommended to use point-to-point link type on the CEs. 

E. If a new CE router is added to the VPLS cloud with a lower interface priority it will become the DIS. 

Answer: AC 


Q89. You are designing an IPv4 any source multicast redundancy solution. Which technology ensures the quickest RP convergence? 

A. Auto-RP 

B. Embedded RP 

C. bootstrap router 

D. MSDP anycast RP 

Answer: D 


Q90. When developing an MVPN design, which performance and scalability consideration must be taken into account? 

A. CE end-to-end PIM adjacency establishment 

B. multicast data sent to all PE routers on the default MDT 

C. RP placement in the multicast VRF 

D. RP placement in the customer network 

Answer: B