★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 350-001 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/350-001-dumps.html


When we confirm the payment for Cisco 350-001 exam items, all the practice resources will be obtainable in Pdf as well as test serp formats. Your Cisco Cisco study guides are supplied with chapter through chapter which tends to make you clearly realize the Cisco Cisco exam preparation. Your Cisco 350-001 Pdf demos are stored up-to-date all the time as well as update regularly according to the latest Cisco certification exam syllabus. 100% money back throughout full in case you fail!

2021 Jan 350 001 dumps:

Q161. BGP-IPv6-0SPF-QOS-Case and Simlet

There is some confusion on this sim and what it is. So I will tell you that it is a window with 4 squares on the left side. Click each one to see the question. Again, there are 4 questions and one topology. Click the `topology' button at the bottom of the sim to see it. There is only one topology for all 4 questions. You do NOT log into any routers. All configuration is provided as text in the question.

NOTE: The actual topology may vary with the routing protocol questions selected for the sim and the number of routers could be as high as R6

Look at the configuration in R3. Of the following routes (30.30.0.0/16, 40.40.0.0/16, and 200.200.0.0/16) Which ones will show up in R2?

Relevant R3 config is the following:

router BGP 1000

neighbor {R2 Loop IP address} remote-as 10

neighbor {R2 Loop IP address} route-map BGP out

neighbor {R2 Loop IP address} send community

route-map 5 BGP permit

match ip address 1

set community no export

route-map 10 BGP permit

access-list 1 30.0.0.0 0.255.255.255

A. 40.40.0.0/16 and 200.200.0.0/16 will show up to R2.

B. 30.30.0.0/16 and 200.200.0.0/16 will show up to R2.

C. 30.30.0.0/16 and 40.40.0.0/16 will show up to R2.

D. 30.30.0.0/16 • 40.40.0.0/16 and 40.40.0.0/16 will show up to R2.

Answer: A


Q162. Which two of these steps are minimum requirements to configure OSPFv3 under IPv6? (Choose two.

A. Configure a routing process using the command ipv6 router ospf [process-id].

B. Add the network statement for the interfaces on which OSPF will run.

C. Configure OSPF on the interface that it will run on.

D. Use the passive-interface command on the interfaces on which OSPF should not run.

E. Enable routing.

Answer: CE


Q163. When troubleshooting a network, the output of the command show interfaces indicates a large number of runts. What is a runt?

A. the number of packets that are discarded because they exceed the maximum packet size of the medium

B. errors created when the CRC generated by the originating LAN station or far-end device does not match the checksum calculated from the data received.

C. the number of packets that are discarded because they are smaller than the minimum packet size of the medium

D. the number of received packets that were iqnored bv the interface because the interface hardware ran low on internal buffers

E. the number of times that the interface requested another interface within the router to slow down

Answer: C


Q164. Refer to the exhibit.

R2 and R3 are routers connected using Ethernet services from a service provider and can receive pings from each other. OSPF is configured as the routing protocol but adjacency is not happening. According to the output of the show commands in the exhibit, what could be the most likely cause of the problem?

A. Ethernet interfaces were configured as point-to-point.

B. Process IDs are not matching.

C. Configured bandwidths do not match on both interfaces.

D. Broadcasts and multicast are not being propagated over the Ethernet services.

E. OSPF cost does not match on both interfaces.

Answer: D


Q165. The EtherChannel between your LAN switch and the Internet router is not load-balancing efficiently. On the switch, there are several workstations with valid IP ranges. Which load-balance algorithms can you use in the switch in order to optimize this load balancing? (Choose four.)

A. source IP address

B. destination IP address

C. per-packet load balance

D. destination MAC address

E. source MAC address

Answer: ABDE


Avant-garde ccie written exam code:

Q166. You are the network administrator of a small Layer 2 network with 50 users. Lately, users have been complaining that the network is very slow. While troubleshooting, you notice that the CAM table of your switch is full, although it supports up to 12, 000 MAC addresses. How can you solve this issue and prevent it from happening in the future?

A. Upgrade the switches

B. Configure BPDU guard

C. Configure VLAN access lists

D. Configure port security

E. Configure Dynamic ARP inspection

Answer: D


Q167. In an 802.1s BPDU, what is the size of the configuration revision number? 

A. 8 bits 

B. 16 bits 

C. 24 bits 

D. 32 bits 

Answer: B


Q168. DRAG DROP

Answer: 


Q169. Which two options does Cisco PfR use to control the entrance link selection with inbound optimization? (Choose two.)

A. Prepend extra AS hops to the BGP prefix.

B. Advertise more specific BGP prefixes (longer mask).

C. Add (prepend) one or more communities to the prefix that is advertised by BGP.

D. Have BGP dampen the prefix.

Answer: AC


Q170. Which statement correctly describes the disabling of IP TTL propagation in an MPLS network?

A. The TTL field from the IP packet is copied into the TTL field of the MPLS label header at the ingress edge LSR.

B. TTL propagation cannot be disabled in an MPLS domain.

C. TTL propagation is only disabled on the ingress edge LSR,

D. The TTL field of the MPLS label header is set to 255.

E. The TTL field of the IP packet is set to 0.

Answer: D