Facts about 300 135 tshoot

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 300-135 Exam Dumps (PDF & VCE):
Available on: https://www.certleader.com/300-135-dumps.html

Your success in Cisco tshoot 300 135 pdf is our sole target and we develop all our ccnp 300 135 braindumps in a way that facilitates the attainment of this target. Not only is our ccnp tshoot 300 135 dumps study material the best you can find, it is also the most detailed and the most updated. ccnp 300 135 Practice Exams for Cisco CCNP Routing and Switching cisco 300 135 are written to the highest standards of technical accuracy.

Q31. - (Topic 7)

The implementations group has been using the test bed to do a ‘proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

Use the supported commands to isolated the cause of this fault and answer the following questions.

What is the solution to the fault condition?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Answer: G

Explanation:

The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

Q32. - (Topic 21)

The implementation group has been using the test bed to do an IPv6 'proof-of-concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).

The fault condition is related to which technology?

A. NTP

B. IPv4 OSPF Routing

C. IPv6 OSPF Routing

D. IPV4 and IPV6 Interoperability

E. IPv4 layer 3 security

Answer: D

Explanation:

Answer: D

As explained earlier, the problem is with route misconfigured tunnel modes on R3. R3 is using tunnel mode ipv6, while R4 is using the default of GRE.

Q33. - (Topic 1)

Which IPsec mode will encrypt a GRE tunnel to provide multiprotocol support and reduced overhead?

A. 3DES

B. multipoint GRE

C. tunnel

D. transport

Answer: D

Q34. - (Topic 5)

Scenario:

A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality.

The OSPF neighbour relationship has been lost between R1 and R3. What is causing this problem?

A. The serial interface in R1 should be taken out of the shutdown state.

B. A neighbor statement needs to be configured in R1 and R3 pointing at each other.

C. The R1 network type should be changed to point-to-multipoint non-broadcast.

D. The hello, dead and wait timers on R1 need to be reconfigured to match the values on R3.

Answer: C

Explanation:

In order for two OSPF routers to become neighbors, they must have matching network types across the links. In this case, we see that R1 has been configured as non-broadcast and R3 is using point to point non-broadcast.

This can be seen by issuing the "show running-config" command on each router, or the "show ip ospf interface" command:

Topic 6, Ticket 1: Switch Port Trunk

Topology Overview (Actual Troubleshooting lab design is for below network design)

. Client Should have IP 10.2.1.3

. EIGRP 100 is running between switch DSW1 & DSW2

. OSPF (Process ID 1) is running between R1, R2, R3, R4

. Network of OSPF is redistributed in EIGRP

. BGP 65001 is configured on R1 with Webserver cloud AS 65002

. HSRP is running between DSW1 & DSW2 Switches

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.

This network consists of four routers, two layer 3 switches and two layer 2 switches.

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP's network. Because the company's address space is in the private range.

R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.

The client workstations receive their IP address and default gateway via R4's DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running

over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

Recently the implementation group has been using the test bed to do a ‘proof-of-concept' on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

Each ticket has 3 sub questions that need to be answered & topology remains same.

Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

Client is unable to ping IP 209.65.200.241

Solution

Steps need to follow as below:-

. When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

Ipconfig ----- Client will be getting 169.X.X.X

. On ASW1 port Fa1/0/ 1 & Fa1/0/2 access port VLAN 10 was assigned which is using IP address 10.2.1.0/24

Sh run ------- & check for running config of int fa1/0/1 & fa1/0/2

====================================================

interface FastEthernet1/0/1switchport mode accessswitchport access vlan 10interface

FastEthernet1/0/2switchport mode accessswitchport access vlan 10

====================================================

. We need to check on ASW 1 trunk port the trunk Po13 & Po23 were receiving VLAN 20 & 200 but not VLAN 10 so that switch could not get DHCP IP address and was failing to reach IP address of Internet

. Change required: On ASW1 below change is required for switch-to-switch Connectivity..

int range portchannel13,portchannel23 switchport trunk allowed vlan none switchport trunk allowed vlan 10,200

Q35. - (Topic 4)

Scenario:

You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn't appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems.

You have received notification from network monitoring system that link between R1 and R5 is down and you noticed that the active router for HSRP group 1 has not failed over to the standby router for group 1. You are required to troubleshoot and identify the issue.

A. There is an HSRP group track command misconfiguration

B. There is an HSRP group priority misconfiguration

C. There is an HSRP authentication misconfiguration

D. There is an HSRP group number mismatch

E. This is not an HSRP issue; this is routing issue.

Answer: A

Explanation:

When looking at the HSRP configuration of R1, we see that tracking has been enabled, but that it is not tracking the link to R5, only the link to R2:

R1 should be tracking the Eth 0/1 link, not 0/0 to achieve the desired affect/

Q36. - (Topic 15)

Use the supported commands to isolated the cause of this fault and answer the following questions.

The fault condition is related to which technology?

A. Under the global configuration mode enter no access-list 10 command.

B. Under the global configuration mode enter no access-map vlan 10 command.

C. Under the global configuration mode enter no vlan access-map test1 10 command.

D. Under the global configuration mode enter no vlan filter test1 vlan-list 10 command.

Answer: C

Explanation:

On DSW1, VALN ACL, Need to delete the VLAN access-map test1 whose action is to drop access-list 10; specifically 10.2.1.3

Q37. - (Topic 19)

Use the supported commands to isolate the cause of this fault and answer the following question.

On which device is the fault condition located?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Answer: B

Explanation:

Start to troubleshoot this by pinging the loopback IPv6 address of DSW2 (2026::102:1). This can be pinged from DSW1, R4, and R3, which leads us to believe that the issue is with R2. Going further, we can see that R2 only has an IPV6 OSPF neighbor of R1, not R3:

We can then see that OSPFv3 has not been enabled on the interface to R3:

So the problem is with R2, related to IPV6 Routing, and the fix is to enable the "ipv6 ospf 6 area 0" command under the serial 0/0/0.23 interface.

Q38. - (Topic 9)

Use the supported commands to isolated the cause of this fault and answer the following questions.

The fault condition is related to which technology?

A. BGP

B. NTP

C. IP NAT

D. IPv4 OSPF Routing

E. IPv4 OSPF Redistribution

F. IPv6 OSPF Routing

G. IPv4 layer 3 security

Answer: A Explanation:

On R1 under router the BGP process Change neighbor 209.56.200.226 remote-as 65002 statement to neighbor 209.65.200.226 remote-as 65002

To see all sample questions go to: 300-135 braindumps questions

Related 300-135 posts: