★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 100-101 Exam Dumps (PDF & VCE):
Available on:
https://www.certleader.com/100-101-dumps.html
You can enjoy free updated Cisco Cisco exam dumps for one year right after purchase. Please consider in our high-quality Cisco practice questions as well as answers which along with visual graphics and exhibits. The actual answers are almost correct as well as verified by the experienced professionals whore working within todays prospering businesses all over the globe. Such as actual Cisco 100-101 certification exams, the practice tests are within multiple- choice format (MCQs), as well as cover each of the Cisco Cisco actual exam topics as well as objectives. Using these speedy and efficient Cisco 100-101 exam preparation materials, you are going to get with the Cisco real exam smoothly on your first try.
2021 Aug ccna 100-101 labs:
Q31. Refer to the exhibit.
SwitchA receives the frame with the addressing shown in the exhibit. According to the command output also shown in the exhibit, how will SwitchA handle this frame?
A. It will drop the frame.
B. It will forward the frame out port Fa0/6 only.
C. It will forward the frame out port Fa0/3 only.
D. It will flood the frame out all ports.
E. It will flood the frame out all ports except Fa0/3.
Answer: E
Q32. Refer to the exhibit.
When running OSPF, what would cause router A not to form an adjacency with router B?
A. The loopback addresses are on different subnets.
B. The values of the dead timers on the routers are different.
C. Route summarization is enabled on both routers.
D. The process identifier on router A is different than the process identifier on router B.
Answer: B
Q33. What command sequence will configure a router to run OSPF and add network 10.1.1.0 /24 to area 0?
A. router ospf area 0 network 10.1.1.0 255.255.255.0 area 0
B. router ospf network 10.1.1.0 0.0.0.255
C. router ospf 1 network 10.1.1.0 0.0.0.255 area 0
D. router ospf area 0 network 10.1.1.0 0.0.0.255 area 0
E. router ospf network 10.1.1.0 255.255.255.0 area 0
F. router ospf 1 network 10.1.1.0 0.0.0.255
Answer: C
Q34. Refer to the exhibit.
A user cannot reach any web sites on the Internet, but others in the department are not having a problem.
What is the most likely cause of the problem?
A. IP routing is not enabled.
B. The default gateway is not in the same subnet.
C. A DNS server address is not reachable by the PC.
D. A DHCP server address is not reachable by the PC.
E. NAT has not been configured on the router that connects to the Internet.
Answer: C
Q35. Refer to the exhibit.
Why was this message received?
A. No VTY password has been set.
B. No enable password has been set.
C. No console password has been set.
D. No enable secret password has been set.
E. The login command has not been set on CON 0
F. The login command has not been set on the VTY ports.
Answer: A
Most up-to-date cisco ccent 100-101 pdf:
Q36. A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link.
The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
Answer: D
Q37. What is the best practice when assigning IP addresses in a small office of six hosts?
A. Use a DHCP server that is located at the headquarters.
B. Use a DHCP server that is located at the branch office.
C. Assign the addresses by using the local CDP protocol.
D. Assign the addresses statically on each node.
Answer: D
Q38. Refer to the exhibit.
Why did the device return this message?
A. The command requires additional options or parameters
B. There is no show command that starts with ru.
C. The command is being executed from the wrong router mode.
D. There is more than one show command that starts with the letters ru.
Answer: D
Q39. What two things does a router do when it forwards a packet? (Choose two.)
A. switches the packet to the appropriate outgoing interfaces
B. computes the destination host address
C. determines the next hop on the path
D. updates the destination IP address
E. forwards ARP requests
Answer: AC
Q40. Which two of these functions do routers perform on packets? (Choose two.)
A. Examine the Layer 2 headers of inbound packets and use that information to determine the next hops for the packets
B. Update the Layer 2 headers of outbound packets with the MAC addresses of the next hops
C. Examine the Layer 3 headers of inbound packets and use that information to determine the next hops for the packets
D. Examine the Layer 3 headers of inbound packets and use that information to determine the complete paths along which the packets will be routed to their ultimate destinations
E. Update the Layer 3 headers of outbound packets so that the packets are properly directed to valid next hops
F. Update the Layer 3 headers of outbound packets so that the packets are properly directed to their ultimate destinations
Answer: BC